Fluke 773 mA Process Clamp Meter

Model 773
mA Process Clamp Meter

Description
Milliamp process clamp meters can measure mA signals without breaking the loop. The Fluke 773 Milliamp Clamp Meter is Fluke's premier mA Clamp Meter, providing you with the best in troubleshooting and process calibration power.

Features

Best in class 0.2% accuracy.
0.01mA resolution and sensitivity.
Measure 4 to 20mA signals without breaking the loop.
Measure mA signals for PLC and control system analog I/O.
Dual backlit display with both mA measurement and percent of 4 to 20mA span.
Measurement spotlight illuminates hard to see wires in dark enclosures.
Detachable clamp with extension cable for measurements in tight locations.
Measure 10 to 50mA signals in older control systems using the 99.9mA range.
Automatically change the 4 to 20mA output for remote testing.
Power saving features, Auto-Off, Backlight timeout extend battery life.
Hold function captures and displays changing measurements.

Measure 4 - 20mA signals with in-circuit measurement.
Simultaneous mA in-circuit measurement with 24V loop power for powering and testing transmitters.
Source 4 - 20mA signals for testing control system I/O or I/P's.
mA output linear ramp or 25% step output.
Automatically change the 4 - 20mA output for remote testing.
DC voltage measurement to verify 24 volt supplies or voltage I/O levels.
Source DC voltage to test input devices that accept a 1.5V or 0 to 10V signals.
Scaled mA output provides a continuous mA signal that corresponds to the 4 - 20mA signal measured by the mA clamp.
Enables milliamp signal logging to a separate logging device without breaking the loop.
Output mA signal enables a logging DMM or other device to record the 4 - 20mA signal without breaking the loop.
mA In/Out: Simultaneously measure the mA signal with the clamp and source signal.
Apply a mA input signal to a device and measure its 4 - 20mA output on devices such as valves or mA isolators.
Voltage output linear ramp or 25% step output.
Automatically change the voltage output for remote testing.

What's the difference between the 77X models?

Models	Fluke 771	Fluke 772	Fluke 773
Measurement	Non-contact mA loop measurement	Integrated mA loop troubleshooting	Advanced process troubleshooting
mA measure, jaw	•	•	•
mA measure, in circuit		•	•
Loop power		•	•
mA source		•	•
DCV measurement			•
DCV source			•
mA scaled output			•
mA in/out			•

Are you spending time:

Taking mA measurements by removing a wire and breaking the loop.
Calling the control room to isolate a loop.
Testing analog input/output on a console.
Troubleshooting devices with mA inputs and outputs.
Repairing intermittent erratic 4 to 20mA loops.
Coming back to the shop to get extra tools.

2009 Plant Engineering Product of the Year Winner

If you need more time in your busy day take a look at the Fluke 773 mA Clamp Meters. It's designed to save you time and money, by eliminating time wasting activities. Now you can troubleshoot and repair 4 to 20mA loops without breaking the loop or bringing down the system.

Here are some specific ways the Fluke 773 Clamp Meters will help you.

Milliamp Clamp Features	Application	How it saves time and money
Measures mA signals for PLC and control system analog I/O without breaking the loop	Measures low level DC current	Correlate process indication with real physical value
Measure output signals from transmitters without breaking the loop	Maintain and troubleshoot process and automation equipment without breaking the loop	No disruption to the process
Detachable clamp with extension cable	Measurements in tight locations	Enables measurements in difficult situations
Source, simulate and measure mA signals in circuit (break the loop)	Confirm non-contact measurement ve the next tool in hand for troubleshooting (source simulate)	Eliminates the need to return to the shop to get a loop calibrator for troubleshooting after finding a bad signal with non-contact measurement
Source and measure Volts DC	Troubleshoot voltage input and output devices	Measure presence of 24V loop power. Measure 1 to 5 or 0 10V process signals. Test chart recorders
4 to 20mA In/Out	Dual channel mA source and measurement for troubleshooting	Source 4-20mA signals into valves and mA signal conditioners and simultaneously measure 4-20mA positioning output signals
4 to 20mA scaled output	Scaled mA output provides a mA signal output representative of the measured mA value	Connect a logging DMM and log the mA signal without breaking the loop
Loop power supply	Power a transmitter	Substitute testing of the installed 24V loop power supply. Power a transmitter and measure its mA output signal for troubleshooting
Dual backlit display with both mA measurement and percent of 4 to 20mA span	Clear measurement presentation	Allows quick measurement evaluation
Measurement Spotlight	Illuminates hard to see wires in dark enclosures	Measurement process is easier and quicker
Measure up to 99.9mA range non-contact	Wide range of measurements	Measures 10 to 50mA signals in older control systems
Automatic power off	After 15 minutes and 2 minutes automatic off for backlight and spotlight	Saves battery life

AEMC | AMPROBE | CIE | FLUKE | HT ITALIA | HODEN | PROVA | POMONA | RAYTECH | SILVERTRONIC
Home | PRODUCTS | SEARCH

Obiat Pty. Ltd.
A.C.N. 003 166 952 A.B.N. 23 003 166 952
Unit 9A/8 Avenue of the Americas, Newington NSW 2127 Australia
P.O. Box 6901 Silverwater NSW Australia 1811

AEMC | AMPROBE | CIE | FLUKE | HT ITALIA | HODEN | PROVA | POMONA | RAYTECH | SILVERTRONIC Home | PRODUCTS | SEARCH

Obiat Pty. Ltd. A.C.N. 003 166 952 A.B.N. 23 003 166 952 Unit 9A/8 Avenue of the Americas, Newington NSW 2127 Australia P.O. Box 6901 Silverwater NSW Australia 1811

AEMC | AMPROBE | CIE | FLUKE | HT ITALIA | HODEN | PROVA | POMONA | RAYTECH | SILVERTRONIC
Home | PRODUCTS | SEARCH

Obiat Pty. Ltd.
A.C.N. 003 166 952 A.B.N. 23 003 166 952
Unit 9A/8 Avenue of the Americas, Newington NSW 2127 Australia
P.O. Box 6901 Silverwater NSW Australia 1811